BEMATECH 4000 TH DRIVER DOWNLOAD

After this, just pull it out of the printer cabinet and you will have the complete control board set on your hands. Who should read this manual? Wrong command sequence Verify if the printer command set is properly configured. Page 31 The next steps are required in order to remove the thermal print head. To separate the connection board from the cutter mechanism, start by loosening the screw that holds the grounding cable located on the side of the equipment, then move away the connection board and disconnect the cables. The correct position to connect this cable is on the CN4 connector as shown on the image on the side.

Uploader: Yolkree
Date Added: 26 June 2014
File Size: 22.76 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 88768
Price: Free* [*Free Regsitration Required]

Removing the Cover Lever Set To remove the lever set it is recommended that the printer cover is hh removed. The information may vary from the printer ready status to critical error warnings, which can lead to module replacement to correct a specific issue.

Fh 31 The next steps are required in order to remove the thermal print head.

If the error message persists, even if the cover is closed, you can verify the following items: When pulling it back, the control board is disconnected from the connection board, located on the frontal portion of the printer.

This manual is intended only for technicians trained by Bematech. Page 5 Introduction This manual provides information on the identification and troubleshooting, test procedures and a list of replacement parts for the MP TH printer. Click on the ‘Load’ button, on the ‘Update firmware’ field.

  ELDO LED DMX DRIVER

Inner Case Make gh the printer is off, open the cover and remove the paper roll. Yh this field it is possible to choose an image to be printed in the MP TH. The recognition of the interface connected to the control board is done with the reading of a code associated to each kind of board through U1, enabled by the SELDEV signal generated by the control board.

Paper dust congestion, generated by the cutter itself can also cause malfunction. Tab ‘Macro’ The tab ‘Macro’ allows tests to be processed in batch mode.

Bematech Mp-4000 Th Fi SM SP Thermal POS Receipt USB Printer

Bematech MP User Manual 36 pages. Tab ‘Additional Commands’ 1. The communication cable may Verify the cable in all its length to be sure that it be damaged or not properly has no indication of physical damage. Page 30 To separate the connection board from the cutter mechanism, start by loosening the screw that holds the grounding cable located on the side of the equipment, then move away the connection board and disconnect the cables.

Product test procedures Technical Support Software This is the technical support software of the product MP TH; with this software you will be able to test all your printer functions. Before turning on the MP TH, make sure that all cables are properly connected; 3.

Index of /download/UTILITARIOS/ECFs/Bematech/Bematech na USB/bemafi32/USB/MP TH FI

The product firmware update can be performed by using the ‘User’s Software’ or the ‘Technical Support Software’. Start by removing the sensors and then the cover lock set.

Try to avoid disassembly, assembly and unnecessary adjustments on the MP TH parts that are working properly; 2. Exploded View Of The Cover Lever 40000 The following part numbers are not necessarily available as stand alone units, as they are part of a replacement kit.

  ACER ASPIRE 5670 ETHERNET CONTROLLER DRIVER

The recognition of the interface connected to the control board is done with the reading of a code associated to each kind of board through U2, enabled by the SELDEV signal generated by the control board.

Page 2 Bematech S. Preventive Maintenance Procedures Clean the area near the cutter bemstech. How this manual is organized Chapter 1 Knowing the product.

Tab ‘Configuration’ At software initialization it will be necessary to configure it before use; this must be the first screen to be accessed before other tabs are used to test the printer functions. Red LED blinking 8 times – Print Mechanism Error On the print initialization, the status of the print head and the paper feed motor picture below are verified. Page of 55 Go. Click on beatech button ‘Get log’ to get a complete report on the printer configuration.

To print the manual completely, please, download it. Removing the Cover Lever Set To remove the lever set it is recommended that the printer cover is also removed.

Remove all the dirt accumulated on the lens. Page 47 There is a sensor on the right side of the printer picture above that notifies it when the cover is closed.